How To Change Blades On Zero Turn Mower

Our team independently selects, reviews, and identifies the best products. We may earn affiliate commissions on purchases made from links on this page. Learn more. This mail was updated on January 5, 2022

Mower blades lose their cut edge over time and volition need to exist replaced.

This article explains how to change blades on zero plow mower for a connected smoothen cutting experience.

Follow the beneath steps to replace the cutting blades in the most common zero-turns including Cub Cadet, Husqvarna, Craftsman, Troy-Bilt, Toro, Swisher, and MTD mowers.

How to change blades on cipher turn mower: step-past-step process

Before y'all beginning, habiliment gloves preferably thick gardening gloves (the blades tin can be quite sharp).

Also, obtain the manufacturer-recommended replacement blades.

The preliminaries

To be safe, start by implementing the usual precautionary steps equally follows:

• Park it on a level footing such equally your driveway.
• Disconnect the mower'south spark plugs.

You're at present all set to brainstorm the nada plough blade removal.

Remove the blade belt

The first step volition exist removing the chugalug. This is vital since it paves the way for the removal of the mower cut deck to permit you admission to the cutting blades.

Procedure:

• Lower the nada turn's deck to the everyman possible setting.
• Locate the condom cover on the left pulley of the mower deck and remove it.
• Now y'all need to roll the cutting blade drive chugalug from the caster on the left blade. You cannot accomplish this without first pushing the belt'due south idler pulley in.

All that remains at this point is for you lot to release the bulldoze belt from its electric clutch. For starters, the electric clutch is directly nether the frame (on the rear end).

How to drain gas from lawn mower without siphon

Remove the cypher turn'due south cutting deck

For many of these types of mowers, the just way to reach the blades is by removing the deck from nether the cypher turn's frame.

Guidelines:

• Await for the deck mounting pins. You take to disconnect them.
• Adjacent, accomplish for the hanging brackets and release them from the deck besides.
• Your next step is pushing the mower deck very slightly forward. Now proceed to release the deck from the front end bracket- information technology should exist easy now that it's more than forwards.
• Finally, pull the deck out.

Remove the mower cutting blades

To admission the cutting blades, turn over the mower deck.

Then:

• Drive a block of 2×4 wood (or any suitable size) between the deck and the cutting blade- you don't desire the blade to plow when unscrewing the bolt.
• With a correctly-sized wrench, remove the bolt mounting the cutting blade – plow it counterclockwise and pull off the cutting blade.
• Remember to place the bolt/nut in a condom location – you lot will shortly demand it.

Mount the new blade

Here is how to approach the installation of your fresh blade:

• Insert the new bract (note the side indicated "This side up" and insert as marked) on the shaft and replace the commodities/nut.
• Tighten the bolt – you even so accept your wrench- until the blade is secured accordingly.

That'southward all for this step.

Re-fix the mower deck

Steps:

• Turn over the mower deck and slide it back in (under the frame).
• Next, reinstall the front bracket and the hanging brackets earlier finally reconnecting the mounting pins to secure the deck.

Best pull behind plug aerator

Reconnect the blade belt

Hither we follow the reverse of the blade belt removal process.

Procedure:

• Reconnect the drive belt onto your unit'due south electric clutch.
• Now roll your blade chugalug dorsum where it was- onto the bract caster on the left. Like I had mentioned, you have to button the belt idler pulley in before this.
• Mount the pulley comprehend back on.

That's it! Re-connect the spark plugs and test the mower to see if information technology cuts as you wish.

How to change blades on naught turn mower: Frequently asked questions (FAQs)

I will tackle some of your nagging questions most naught turn blade change.

How practice I loosen a backyard mower blade? (Lawn mower bract removal direction)

In most cases, you plow your z-turn mower'south blade retaining bolt counterclockwise (to the left) carefully.
The bract should merely fall off as soon as you've removed the holding nut.

How do I know that it's time to modify the blades?

The platonic matter to do is to go along an eye on the quality of the cut when mowing.
And you should consider installing new blades the moment you start observing a shambolic cut, despite you lot having sharpened the blades prior to cutting (This may be due to the blades beingness worn down extensively).
Importantly, hither we are assuming that your blades are not fitted upside-down (confirm if in doubt).
The other telltale sign is when y'all notice that your blade is clearly damaged – perhaps you hit a rock or co-operative when mowing.

How often should lawn mower blades be replaced?

This is a question of usage (how often yous mow) and proper bract maintenance.
That said, former y'all may only require to change their bract once a year unless you own a commercial unit- these will obviously need more frequent changes fifty-fifty in one day.

Like yous have seen, replacing the blades should be straightforward and you don't need to involve an expensive technician.

The expert matter is that you'll principal how to change blades on nix plow mower by the time you practice it twice or thrice.

The steps may, of course, be slightly different for your specific model and you should refer to your owner's manual first.

If possible, accept a spare set of mower blades to avoid inconveniences when information technology's to modify the blades.

Useful video (blades replacement on Husqvarna rz-series aught turn)

Zilch turn mowers with snowblower attachment

Source: https://threetwohome.com/how-to-change-blades-on-zero-turn-mower/

Posted by: duartetoneady.blogspot.com

Share this post